Skip to content
Aslams is now Qasre Health
Qasre Health
Browse all products

Qasre Health innovation

Auto Relief

The bed moves with the body, not against it.

Every time a hospital bed raises the backrest or knee section, it rotates around a hinge. On most beds, that hinge sits at the frame, but the patient's body bends at the hips. That mismatch pushes the patient down the bed, compresses the abdomen, and drags skin against the mattress. Auto Relief moves the bed's pivot points closer to where the body actually bends, so elevation feels natural and back strain is reduced.

HipPivot
With the pivot near the hip, bed and body rise around the same point.

Why conventional beds strain the back

When the backrest pivots at frame level, well below the patient's hip joint, the bed and the body rotate around different centres. As the head section rises, the backrest travels a different path from the patient's torso.

  • Sliding: patients slide toward the foot end and must be pulled back up, often several times a day.

  • Back strain: the lower back loses support and the abdomen is compressed as the body folds at the wrong point.

  • Shear: skin over the sacrum is dragged against the mattress, a known contributor to pressure injuries.

  • Caregiver load: repeated repositioning costs nursing time and risks back injury to staff.

These aren't problems a softer mattress can solve. They're geometry problems, so we solved them with geometry.

HipPivot
Conventional bed: the backrest pivots at frame level, below the hip, and the patient is pushed toward the foot end.

Pivots that follow the hips

Auto Relief relocates the pivot points of the head and knee sections upward, toward the patient's natural hip rotation centre. Instead of the bed folding at the frame and the body trying to keep up, bed and body rotate around nearly the same point.

The patient stays where they were positioned, the back stays supported through the movement, and the mattress moves with the skin rather than across it.

Before · frame pivot

HipPivot

After · Auto Relief Pro pivot

HipPivot

Two levels of relief

Auto Relief

Pivots raised to the body

Pivot points are raised from the frame to approximately 70% of the mattress height. This brings the rotation axis much closer to the patient's body, reducing sliding and back strain during routine head and knee elevation.

Best for: general wards, recovery rooms, long-stay care.

Our closest alignment

Auto Relief Pro

Pivots at the hip

Pivot points are positioned near the estimated hip rotation centre of the average Indian patient, derived from the National Institute of Design's anthropometric data on Indian adults. Our closest alignment between bed and body.

Best for: ICUs, critical care, patients elevated for long periods.

Why the average Indian patient?

Most bed geometries are designed around Western anthropometric data, and published research on hip rotation centres comes almost entirely from non-Indian populations measured standing. Auto Relief Pro is built on Indian anthropometric data from the National Institute of Design, applied to the positions a hospital bed actually puts patients in.

The science behind Auto Relief

Designed around Indian bodies

Most hospital beds are engineered around anthropometric data from American, European, or East Asian populations. Studies of Indian adults show meaningfully different body proportions. Research by the ICMR's National Institute of Occupational Health recorded a mean stature of 1647 mm among adult men in Odisha, well below the reference figures used in Western bed design.

But height alone doesn't tell you where a pivot should go. Published hip rotation centre data is measured with patients standing and viewed from the front, which says little about where the hip sits when a patient lies on a mattress and the backrest rises.

So we worked from the most complete Indian dataset available. Auto Relief Pro's pivot is estimated from the National Institute of Design's anthropometric survey of Indian adults, the standard reference for ergonomic design in India, applied to a patient lying and sitting on a hospital bed with a standard 4-inch mattress.

How Auto Relief compares

MeasureConventional bedsAuto ReliefAuto Relief Pro
Pivot locationFrame level~70% of mattress heightNear estimated Indian hip rotation centre
Patient sliding during elevationHighReducedMinimal
Back support through the movementLost as bed foldsLargely maintainedMaintained
Shear on sacral regionHighReducedLowest
Repositioning neededFrequentLess frequentRarely
Recommended for—General wards, recovery, long stayICU, critical care, high-risk patients

Better for everyone at the bedside

For patients

More comfortable elevation, less sliding, better back support, and lower shear on vulnerable skin.

For nurses and caregivers

Fewer repositioning manoeuvres per shift, saving time and reducing the physical load and injury risk of pulling patients up the bed.

For hospitals

Support for pressure-injury prevention protocols, a better patient experience, and a bed that works with clinical routines.

Built into every movement

Head and knee elevation on Qasre Health beds is driven by electric actuators. With Auto Relief, the linkage geometry is redesigned so the effective rotation axes of the backrest and thigh sections sit above the frame. There are no extra controls and no extra steps for staff. The relief is built into every elevation, every time.

Conventional
Auto Relief
Auto Relief Pro

Frequently asked questions

Does Auto Relief need any extra operation by staff?

No. It works automatically whenever the head or knee section is raised.

Which beds offer Auto Relief and Auto Relief Pro?

Auto Relief is standard on the Enigma Premium beds. Auto Relief Pro is available on the Enigma Premium configurations B5RP-S000-0649 and B3RP-CL00-0775.

See the difference at 45 degrees.

Raise the head of a conventional bed and an Auto Relief bed side by side, and watch where the patient ends up. Book a demo and we'll show you.